NH3 / N2 / O2 Non-Premixed Flame in a 10 kW Experimental Furnace – Characteristics of Radiative Heat Transfer

Presented on November 1, 2017 during the NH3 Fuel Conference 2017

Authors Ryuichi Murai Ryohei Omori Ryuki Kano Yuji Tada Hidetaka Higashino Noriaki Nakatsuka Jun Hayashi Fumiteru Akamatsu Osaka University

Download this Presentation Download a PDF version of this presentation.

Abstract

There are severe issues on increasing amount of carbon dioxide (CO2) emission in the world. Many studies are devoted on alternative fuels. One of superior candidates is the utilization of hydrogen energy which can realize a low-carbon and hydrogen-based society. Ammonia might play an important role which is zero emission of CO2, and is useful for hydrogen energy carrier as a clean energy. Additionally, ammonia is an easily-liquefiable fuel with pressure of about 0.86 MPa and temperature of 293 K. Commercially, ammonia is produced in large quantity by the Haber–Bosch process. It is also to be produced by using catalyst with renewable energy sources, such as wind energy and solar energy.

The ammonia has advantages to be used as an alternative fuel. The thermo-physical properties of an ammonia fuel are similar to those of propane. Lower heating value of ammonia is 3358 (kcal/m3N). Although it is smaller than that of methane (8557 (kcal/m3N)), it is larger than that of hydrogen (2570 (kcal/m3N)). Therefore, the ammonia has a possibility to be employed directly to industrial furnaces, gas turbines and reciprocating engines as a fuel. Also, the ammonia does not emit CO2 during its combustion process. A large amount of CO2 reduction is expected in case of introducing an ammonia gas as a fuel to boilers and industrial furnaces.

However there are two main issues applying ammonia combustion as a fuel to boilers and industrial furnaces. First, ammonia doesn’t contain carbon atoms, which results in emitting less radiative heat flux than methane combustion because of lack in CO2 and soot. Secondly, fuel-NOx emission is particular concern, because the ammonia molecule contains nitrogen atom itself as fuel-N.

In this situation, we established the 10kW experimental furnace to study the radiative heat flux, the radiation spectra and NOx emission under the condition of the ammonia fuel combustion and the oxygen enriched ammonia combustion.

The furnace is 1400 mm long and its inner wall is surrounded with the adiabatic material. On a top of the furnace there are six ports equipped with thermocouples. On a bottom of a furnace, there also are six ports for measuring heat flux and emission spectrum from the inner wall and the flame. For the thermal emission spectrum measurement, we installed the spectrum detector instead of the heat flux detector. Therefore, we can compare heat flux data with spectrum ones at the same position. We introduced fuels and oxidizers using mass flow controllers to the banner of which burner nozzle had coaxial double tube and fuel flows through the center tube and oxidizer flows through its outer tube. This structure generated the coaxial jet flame in our experimental furnace. The heat flux detector, of which detection area is a circular shape with a diameter of 10 mm, can eliminate the heat convection and only measure the radiative heat flux.

The results that became clear in this study were shown below:

We developed the infrared spectral measurement system and the radiative heat flux detector one of which detection area was 38 mm2.
In the oxidizer with 21% of O2 concentration, the wall temperature inside the furnace decreased about 200 K and the maximum value of heat flux under ammonia non-premixed flame also became about 22% lower than that under the condition of the methane/air non-premixed flame.
The oxidizer with 30% of O2 concentration could result in the higher temperature than that in the methane/air non-premixed condition and have 1.4 times intensity of total radiative heat flux.
The oxygen enriched combustion can make nearer to the peak position of the radiative heat flux.
The NOx emission can be reduced with the technology optimized nozzle structure.

Topics Ammonia Combustion Emissions Testing Fuel Comparisons NOx Emissions

Authors murai@combu.mech.eng.osaka-u.ac.jp Ryohei.Omori@ammoniaenergy.org kano@combu.mech.eng.osaka-u.ac.jp tada@combu.mech.eng.osaka-u.ac.jp higashino@cpdc.eng.osaka-u.ac.jp nakatsuka@mech.eng.osaka-u.ac.jp hayashi@energy.kyoto-u.ac.jp akamatsu@mech.eng.osaka-u.ac.jp kimio.iino@tn-sanso.co.jp Yasuyuki.Yamamoto@tn-sanso.co.jp Yoshiyuki.Hagiwara@tn-sanso.co.jp

Madoqua Power2X webinar on Tuesday, November 26

Please join us for this informative webinar. Click here to register and get the details!

Annual Conference highlights industry advancements

It was an exciting three days in New Orleans with 300 attendees from 22 countries participating in our 21st AEA Annual Conference. Thank you to our generous sponsors and to all those who attended the conference. Stay tuned for a recap of the events and sessions. Presentations from all the sessions will be posted shortly.

Featured content

In 2023, AEA reached many milestones. Read about them in our 2023 Annual Report.